
Personalized coasters in slate, wood or glass: what the laser engraves
A set of four or six coasters engraved with initials, the map of a bay or a logo. The workshop's laser engraves slate, wood or glass, made to order in Saint-Siméon-de-Bonaventure.

Yes. The workshop can laser-engrave personalized coasters in slate, hardwood or glass, with initials, a map or a logo. The material changes the result: slate generally comes out pale grey, wood brown and glass frosted white.
This post compares the three materials, covers what to put on a coaster, explains how a set of four or six comes together and how to look after it. Every set is made to order, and whether it can be done, and when, is confirmed on the first call.
Slate, wood or glass: what does laser engraving look like on each?
The workshop's 80 W CO2 laser marks slate, hardwood and glass, as of November 2026. Its engraving bed is 36 x 18 in (915 x 458 mm) and a typical coaster is about 4 in (10 cm) across, so several pieces fit on one sheet. Each material gives its own result:
- Slate: this rock splits into thin sheets, and its dark matte surface makes the engraving show up pale grey. The contrast is strong.
- Hardwood, such as maple or cherry: the wood turns brown under the laser. The grain stays visible in the engraving, and each coaster differs a little from the next.
- Glass: the laser leaves a frosted white mark. Simple shapes read best on clear glass.
Our guide to engraving materials and objects goes through these results one material at a time.
To choose, start from the use. Slate suits a coffee table and a restrained room. Wood goes with the warm furniture of a cottage. Glass fits a bar or a counter, where transparency matters. A set can also mix two materials, which you can discuss with the workshop.
| Material | Engraved result | What engraves well | Care |
|---|---|---|---|
| Slate | Pale mark on dark stone | Initials, map, simple logo | Damp cloth, then dry |
| Hardwood | Brown mark, grain visible | Initials, map, patterns | Damp cloth, do not soak |
| Glass | Frosted white mark | Simple shapes, clean logo | Hand wash |
Every set is made to order. The exact result is confirmed on the first call, based on the material and the design.
What to engrave on a coaster: initials, a map or a logo?
A coaster is small. A simple design reads better on it than a busy one. These are the most common choices:
- Initials or a monogram: one to three letters, centred, sometimes in a circle. The most understated choice for a wedding or housewarming gift.
- A map: the outline of the Baie-des-Chaleurs, the Gaspé Peninsula or a lake, with a dot for the village. Small details are simplified so they stay legible.
- A logo: for a shop, a B&B or a restaurant. Send a vector file (SVG, PDF or AI) if you have one, otherwise a sharp high-resolution image.
- A regional motif: a lighthouse, a northern gannet, a spruce.
For any text, send the exact wording in writing. We check every letter before the machine starts, because an engraving cannot be erased. For a logo across several pieces, laser engraving repeats exactly the same file on the whole set.
Shape matters too. A round coaster shows off a map or a centred monogram. A square coaster suits a rectangular logo or a motif that repeats across the table. The shape and the dimensions are confirmed on the first call, based on the material you choose.

How many coasters in a set, and what goes underneath?
A set is most often four or six coasters, sometimes eight for a large table. The workshop can make other quantities to order. The design can be spread across the set in several ways:
- The same motif on every piece: the simplest, one file engraved four or six times.
- Different initials on each coaster: one per family member or guest.
- A split motif: an idea to discuss, such as a map cut across four coasters that fit together.
- A felt or cork backing: it keeps furniture from getting scratched. It can be added on request, and whether it can be done is confirmed on the first call.
A set can also be given in an engraved wooden box, another of the workshop's wooden Christmas gift ideas.
For a gift, think about how many people sit around the table rather than the size of the set. Six coasters cover a living room with guests, and four are enough for a couple. The number is yours to decide, before the quote.
How do you look after engraved coasters?
A coaster takes water, condensation and sometimes heat. A few simple habits keep it in good shape:
- Slate: wipe with a damp cloth, then dry. Avoid abrasive cleaners on the engraving.
- Wood: wipe quickly with a damp cloth and dry. Do not let it soak, and keep it out of the dishwasher. A wood oil can refresh the surface when needed.
- Glass: hand wash in warm soapy water. As a precaution, keep the frosted mark out of the dishwasher.
- In every case, avoid very hot dishes and mugs: a coaster is made for glasses.
This advice is general. For a specific set, the workshop gives the care for your chosen material when you order.
How to order personalized coasters
An order follows four short steps.
- Describe the set: the material, the number of coasters, what to engrave, the shape (round or square).
- Send the exact text, the logo or the image of the map you want.
- The workshop confirms whether it can be done and when, then you receive a quote. Nothing starts before you approve it.
- Pick the set up in Saint-Siméon-de-Bonaventure, or have it delivered within the Baie-des-Chaleurs. Elsewhere in the Gaspé, delivery is on request, case by case.
For coasters with a business logo, meant for clients or staff, read our post on engraved corporate gifts.
Slate is a fine-grained metamorphic rock that splits into sheets, according to the Wikipedia article Slate.
A set of coasters to engrave?
Tell us the material, the design and the quantity. In business since 1994, the workshop tells you plainly what can be made, and when. Phone: 418-534-4167.
Frequently asked questions
Slate, wood or glass: which material for a personalized coaster?
Slate gives a pale, high-contrast engraving on dark stone. Wood gives a brown mark that shows the grain. Glass gives a frosted mark, more discreet. Tell us the use and the design and we confirm the result before you order.
Can you engrave a map or a logo on a coaster?
Yes, to order. A map is simplified so it stays legible on a piece about 4 in (10 cm) across. For a logo, send a vector file if you have one, otherwise a sharp high-resolution image.
Can I order one coaster, or only a full set?
The workshop can make one piece or a set, to order. A set is most often four or six coasters. Quantity and schedule are confirmed on the first call.
Can you add felt under the coasters?
A felt or cork backing keeps furniture from getting scratched. It can be added on request. We confirm whether it can be done on the first call, based on the material and the shape of the coaster.
How do I clean an engraved coaster?
Wipe slate and wood with a damp cloth, then dry. Hand wash glass. Do not soak wood, and keep engraved pieces out of the dishwasher. The workshop gives the care for your chosen material when you order.



