Reference illustration: pale maple box with a lid engraved with a branch pattern, resting on a blond wood table beside cards and a newborn's bracelet, in daylight
Engraved gifts

Engraved wooden keepsake box: choosing the size, the wood and the engraving

A wooden keepsake box holds cards, jewellery, letters or a newborn's hospital bracelet. The lid carries a name, a date or a pattern engraved by laser. Here is how to choose the size, the wood, the joinery and the engraving.

Reference illustration: close-up of the corner of a pale birch box, with a clean mitre joint and a lid slightly open to show the bare wood inside
Reference illustration: a maple keepsake box with an engraved lid.

A wooden keepsake box is a small chest closed by an engraved lid, built to hold things you care about: cards, jewellery, letters, a baby's first keepsakes. Atelier Multidécor can make a personalized wooden box to order at its workshop in Saint-Siméon-de-Bonaventure, in the Gaspé Peninsula, with a laser-engraved lid.

This post follows the choices of an order, in sequence: the occasion, the size, the wood, the joinery, the lid engraving and the inside. Every box is a made-to-order piece: whether it can be made, and when, is confirmed on the first call.

What occasions call for a wooden keepsake box?

A keepsake box is given when objects deserve a place of their own. The occasion decides the engraved text and the size of the box:

  • a birth: the hospital bracelet, the first booties, congratulation cards, with the name and birth date on the lid;
  • a wedding: the invitation, handwritten vows, a memento of the ceremony, with the first names and the date;
  • the memory of a parent: letters, medals, a watch, with a name and years;
  • postcards, photos or family letters, gathered in one box;
  • jewellery, stored in a box sized for it.

A box holds things you touch and reread. If you are looking for a tribute to put on display, read our guide to the custom engraved commemorative plaque.

What size of keepsake box should you choose?

Start by measuring the largest object the box must hold, then allow a little room all around. The table gives common sizes for things people often store in these boxes.

For example, a box 4 in (10 cm) deep takes a stack of cards and letters. A flat box 2 in (5 cm) deep suits a few photos and some jewellery.

Think about what will be added later. A baby's box fills up over years, and a wedding box grows with each anniversary. A little spare room is better than a lid that no longer closes.

Common sizes of things to store
ItemCommon sizeWorth knowing
Photo4 x 6 in (10 x 15 cm)The inside must run a little larger than the print
Playing card2 1/2 x 3 1/2 in (6.4 x 8.9 cm)Measure the thickness of the deck too
No. 10 envelope4 1/8 x 9 1/2 in (10.5 x 24.1 cm)Holds a letter-size sheet folded in three
Letter-size sheet8 1/2 x 11 in (21.6 x 27.9 cm)Stores folded, or flat in a larger box
Jewellery or watchVariesMeasure the longest piece

These are common standards. A made-to-order box is fitted to your objects, not to a catalogue module.

Reference illustration: close-up of the corner of a pale birch box, with a clean mitre joint and a lid slightly open to show the bare wood inside
Reference illustration: the corner and lid of a birch keepsake box.

Which wood for an engraved keepsake box?

Laser engraving browns the surface of the wood. The paler the wood, the more the pattern stands out. Here are three guides:

  • maple: a pale hardwood with a fine grain, which keeps a name, a date or a fine pattern crisp;
  • birch: a pale wood with a discreet grain and a slightly warmer tone;
  • a darker wood, such as walnut or cherry: the engraving has softer contrast, which suits short text and a large pattern.

The grain of the wood runs through the engraving. For fine text, an even grain gives a crisper result. Which species are available for your box we confirm on the first call, and the finishing is done by hand.

Which joint for a solid wooden box?

The joint holds the sides together, and it shows on the finished box. Three joints common in cabinetmaking suit a small chest:

  • the mitre: corners are cut at 45 degrees, and the wood grain can continue around the box, giving discreet corners;
  • the dovetail: wedge-shaped pins and tails interlock, resist being pulled apart and show on the sides as a mark of the trade;
  • the box joint: alternating rectangular fingers, simpler to lay out, also visible on the sides.

The choice depends on the wood, the size and the look you want. The lid is decided at the same time: resting, hinged or sliding, depending on use. Every box is a custom project: the workshop confirms on the first call which joint and hardware are possible.

What can be engraved on the lid and inside the box?

The workshop's 80 W CO2 laser engraver marks wood on a 36 x 18 in (915 x 458 mm) bed, as of November 2026. A box lid fits well within it. It can carry:

  • a first name and a birth date;
  • the first names and the date of a wedding;
  • initials or a monogram;
  • a simple pattern: a branch, a lighthouse on the coast, the map of a bay;
  • a short dedication or an important date, in simple lettering;
  • a short phrase engraved inside the lid, visible only when it is opened.

Send us the exact text in writing. We check every name and date before the machine starts, because an engraving cannot be erased. For the inside, the box can stay bare wood or take compartments. What is possible is confirmed on the first call.

How do you order a made-to-order keepsake box?

A box follows the steps of a small cabinetry project:

  • Describe the idea by phone or email: the occasion, what the box will hold, the wood you prefer, the text to engrave.
  • The workshop confirms whether the box can be made and whether the schedule allows it for your date.
  • You receive a quote. Nothing starts before you approve it.
  • Pick the box up at the workshop in Saint-Siméon-de-Bonaventure, or have it delivered within the Baie-des-Chaleurs. Elsewhere in the Gaspé, delivery is discussed on request, case by case.

A keepsake box makes a Christmas or newborn gift that is built to be kept. See our Christmas gift ideas in wood for other engraved pieces.

The principle of the dovetail joint is described in the Wikipedia article Dovetail joint.

A keepsake box to make?

Tell us the occasion, what the box will hold and the text to engrave. In business since 1994, the workshop tells you plainly what can be made, and when. Phone: 418-534-4167.

Frequently asked questions

What size of keepsake box should I choose?

Measure the largest object to store, then add a little room all around. A common photo is 4 x 6 in (10 x 15 cm) and a playing card is 2 1/2 x 3 1/2 in (6.4 x 8.9 cm). Also leave space for what will be added over the years.

Can you engrave a name or a date on the lid?

Yes. The laser engraves a first name, a date, initials or a simple pattern on the wood. Send the exact text in writing. We check every name and date before engraving, because an engraving cannot be erased.

Which wood is best for a personalized keepsake box?

A pale wood with a fine grain, such as maple or birch, gives a crisp engraving. A darker wood, such as walnut, gives softer contrast. Available species are confirmed on the first call.

Can the inside of the box be customized?

The inside can stay bare wood, or the box can take compartments, and a phrase can be engraved under the lid. The workshop confirms on the first call what is possible for your box.

How do I order a custom wooden chest?

Describe the occasion, the contents and the text by phone or email. The workshop confirms feasibility and schedule. You receive a quote, and nothing starts before you approve it.